J's Racing Front Camber Joint S2 - S2000 AP1/2
$311.00
SKU
JS-CAJ-S1-S2
Fits all S2000 model years.
Anodized Forged 6061 CNC Aluminum construction. Includes laser engraved J's Racing stamp
Made in Japan.
The J's Racing Front Camber Joint S2 allows for additional front camber by shifting the camber range to 3°-6° of camber without roll center adjustment.
By redesigning the previous model, this new camber joints includes 9mm of built in roll center adjustment in addition to the negative camber adjustment.
Material : Forged aluminum 6061
The surface is anodized red with a laser carved ‘J’s Racing” seal
Ball joint S45C
Boll stud SCM435 HB195-260, Fluctuation angle 33 degree all around
The front camber angle can be adjusted to the stock + 2 degree (+ 3 degree for S2).
The front roll center value can be adjusted back to the correct one. The insufficient negative camber is always a problem for S2000. This product creates enough negative front camber by locating the lower ball joint at an eccentric angle from the center. The product also corrects the front lower arm position back close to horizontal, so that the correct geometry is restored with the accurately adjusted roll center. [When you reduce the ride height, the front lower arm position becomes like a separated letter V]
Adjustable range: 2 to 3 degrees (3 to 5 degrees for S2)
Roll Center Adjustment: 9mm
Ride height: Recommended to the vehicle whose height is reduced more than 40mm
Included in the kit:
Camber Joint S1 x2
Clip x2
Castle nut x2
* The stock bolts are to be reused or use new stock ones. Please apply the correct tightening torque. After the installment, it is necessary to properly adjust the ride height and alignment. It is highly recommended to check the tightening condition of the bolt & nut periodically. [Always check it before the track event or race]
Anodized Forged 6061 CNC Aluminum construction. Includes laser engraved J's Racing stamp
Made in Japan.
The J's Racing Front Camber Joint S2 allows for additional front camber by shifting the camber range to 3°-6° of camber without roll center adjustment.
By redesigning the previous model, this new camber joints includes 9mm of built in roll center adjustment in addition to the negative camber adjustment.
Material : Forged aluminum 6061
The surface is anodized red with a laser carved ‘J’s Racing” seal
Ball joint S45C
Boll stud SCM435 HB195-260, Fluctuation angle 33 degree all around
The front camber angle can be adjusted to the stock + 2 degree (+ 3 degree for S2).
The front roll center value can be adjusted back to the correct one. The insufficient negative camber is always a problem for S2000. This product creates enough negative front camber by locating the lower ball joint at an eccentric angle from the center. The product also corrects the front lower arm position back close to horizontal, so that the correct geometry is restored with the accurately adjusted roll center. [When you reduce the ride height, the front lower arm position becomes like a separated letter V]
Adjustable range: 2 to 3 degrees (3 to 5 degrees for S2)
Roll Center Adjustment: 9mm
Ride height: Recommended to the vehicle whose height is reduced more than 40mm
Included in the kit:
Camber Joint S1 x2
Clip x2
Castle nut x2
* The stock bolts are to be reused or use new stock ones. Please apply the correct tightening torque. After the installment, it is necessary to properly adjust the ride height and alignment. It is highly recommended to check the tightening condition of the bolt & nut periodically. [Always check it before the track event or race]
Fits all S2000 model years.
Anodized Forged 6061 CNC Aluminum construction. Includes laser engraved J's Racing stamp
Made in Japan.
The J's Racing Front Camber Joint S2 allows for additional front camber by shifting the camber range to 3°-6° of camber without roll center adjustment.
By redesigning the previous model, this new camber joints includes 9mm of built in roll center adjustment in addition to the negative camber adjustment.
Material : Forged aluminum 6061
The surface is anodized red with a laser carved ‘J’s Racing” seal
Ball joint S45C
Boll stud SCM435 HB195-260, Fluctuation angle 33 degree all around
The front camber angle can be adjusted to the stock + 2 degree (+ 3 degree for S2).
The front roll center value can be adjusted back to the correct one. The insufficient negative camber is always a problem for S2000. This product creates enough negative front camber by locating the lower ball joint at an eccentric angle from the center. The product also corrects the front lower arm position back close to horizontal, so that the correct geometry is restored with the accurately adjusted roll center. [When you reduce the ride height, the front lower arm position becomes like a separated letter V]
Adjustable range: 2 to 3 degrees (3 to 5 degrees for S2)
Roll Center Adjustment: 9mm
Ride height: Recommended to the vehicle whose height is reduced more than 40mm
Included in the kit:
Camber Joint S1 x2
Clip x2
Castle nut x2
* The stock bolts are to be reused or use new stock ones. Please apply the correct tightening torque. After the installment, it is necessary to properly adjust the ride height and alignment. It is highly recommended to check the tightening condition of the bolt & nut periodically. [Always check it before the track event or race]
Anodized Forged 6061 CNC Aluminum construction. Includes laser engraved J's Racing stamp
Made in Japan.
The J's Racing Front Camber Joint S2 allows for additional front camber by shifting the camber range to 3°-6° of camber without roll center adjustment.
By redesigning the previous model, this new camber joints includes 9mm of built in roll center adjustment in addition to the negative camber adjustment.
Material : Forged aluminum 6061
The surface is anodized red with a laser carved ‘J’s Racing” seal
Ball joint S45C
Boll stud SCM435 HB195-260, Fluctuation angle 33 degree all around
The front camber angle can be adjusted to the stock + 2 degree (+ 3 degree for S2).
The front roll center value can be adjusted back to the correct one. The insufficient negative camber is always a problem for S2000. This product creates enough negative front camber by locating the lower ball joint at an eccentric angle from the center. The product also corrects the front lower arm position back close to horizontal, so that the correct geometry is restored with the accurately adjusted roll center. [When you reduce the ride height, the front lower arm position becomes like a separated letter V]
Adjustable range: 2 to 3 degrees (3 to 5 degrees for S2)
Roll Center Adjustment: 9mm
Ride height: Recommended to the vehicle whose height is reduced more than 40mm
Included in the kit:
Camber Joint S1 x2
Clip x2
Castle nut x2
* The stock bolts are to be reused or use new stock ones. Please apply the correct tightening torque. After the installment, it is necessary to properly adjust the ride height and alignment. It is highly recommended to check the tightening condition of the bolt & nut periodically. [Always check it before the track event or race]
| Manufacturer Product Code | JS-CAJ-S1-S2 |
|---|---|
| Product Types | Suspension System |
| Manufacturer | J's Racing |
| Model Year | 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 |
| Make | Honda |
| Model | S2000 |
| Item Description | Fits all S2000 model years. Anodized Forged 6061 CNC Aluminum construction. Includes laser engraved J's Racing stamp Made in Japan. The J's Racing Front Camber Joint S2 allows for additional front camber by shifting the camber range to 3°-6° of camber without roll center adjustment. By redesigning the previous model, this new camber joints includes 9mm of built in roll center adjustment in addition to the negative camber adjustment. Material : Forged aluminum 6061 The surface is anodized red with a laser carved ‘J’s Racing” seal Ball joint S45C Boll stud SCM435 HB195-260, Fluctuation angle 33 degree all around The front camber angle can be adjusted to the stock + 2 degree (+ 3 degree for S2). The front roll center value can be adjusted back to the correct one. The insufficient negative camber is always a problem for S2000. This product creates enough negative front camber by locating the lower ball joint at an eccentric angle from the center. The product also corrects the front lower arm position back close to horizontal, so that the correct geometry is restored with the accurately adjusted roll center. [When you reduce the ride height, the front lower arm position becomes like a separated letter V] Adjustable range: 2 to 3 degrees (3 to 5 degrees for S2) Roll Center Adjustment: 9mm Ride height: Recommended to the vehicle whose height is reduced more than 40mm Included in the kit: Camber Joint S1 x2 Clip x2 Castle nut x2 * The stock bolts are to be reused or use new stock ones. Please apply the correct tightening torque. After the installment, it is necessary to properly adjust the ride height and alignment. It is highly recommended to check the tightening condition of the bolt & nut periodically. [Always check it before the track event or race] |
Other Products You May Be Interested In
-
![ASM SRE 3-Way Damper Kit - S2000 AP1/2]()
ASM SRE 3-Way Damper Kit - S2000 AP1/2$13,500.00 -
![Spoon Clutch Cover - S2000 AP1]()
Spoon Clutch Cover - S2000 AP1$525.00
|
|
